亚洲va中文字幕欧美不卡-亚洲va在线va天堂成人-亚洲va在线va天堂va手机-亚洲va在线va天堂va888www-久一视频在线-久污tv

Welcome to Shenzhen Zhongyuan Plastic Co., Ltd!

News



Tel:(0755)27151698
Fax:(0755)27150611
Mailbox:szzyzcl@163.com / szzy@szzy99.com
Add:Building A1 and A2, No.1 Industrial Zone, yuliu property company, Gongming town, Bao'an District, Shenzhen
Company dynamics

當前位置:

首頁 News Company dynamics

Causes of overflow during injection mold processing

Release time:2021-07-09


Overflow, also known as flash and overflow, usually occurs at the opening and closing position of the mold. For example, the parting surface of the mold, the gap of the insert and the hole of the ejector rod. If the overflow cannot be eliminated in time, it will lead to local collapse of the injection mold, and even permanent damage will be formed in serious cases. In addition, the overflow of insert gap and ejector pin hole will also lead to waste products stuck on the mold, affecting the demoulding process. So why does the injection mold overflow in the processing process? How to deal with the overflow phenomenon? The following editor will answer for you.

1、 Equipment

1. The improper installation and adjustment of the mold closing of the injection molding machine or the uneven elbow mechanism will cause the mold to not reach the due parallelism, presenting the phenomenon that one side of the mold is tightly closed and the other side is not tightly connected, which is easy to show overflow during the injection process.

2. There is a problem with the parallelism of the injection molding machine itself, and the uneven force distribution of the pull rod will also lead to the failure of the mold to close tightly and form a material overflow condition.

3. The injection molding machine has serious wear of the check ring, too much wear of the screw, lack of the set injection volume of the barrel, too small buffer pad and other conditions, which are likely to cause material overflow, so the operator must stop repairing or changing parts in time.

II. Mold

1. Poor accuracy of mold parting surface

The movable template (such as the middle plate) is deformed and warped, there are foreign objects on the parting surface, and there are prominent skid marks and burrs on the periphery of the mold frame. These conditions will lead to the overflow of the injection mold.

2. Unreasonable mold design

(1) If the opening position of the mold cavity is too biased, the mold will have excessive unilateral tension during the injection process, resulting in overflow.

(2) Polyethylene, polypropylene and other plastic materials have good mobility, and their viscosity in the molten state is low, so it is easy to enter the gap of the mold. Therefore, when manufacturing high-precision molds, operators should try to feed in the thick part of the mold, so as to avoid overflow and affect the integrity of the mold products.

(3) The poor matching accuracy of the sliding core of the mold or the offset between the fixed core and the cavity device will also lead to the appearance of the overflow condition.

(4) As for the multi cavity mold, the designer should pay attention to the reasonable design of the runner and gate, otherwise it will lead to uneven filling force and overflow.

3、 Process aspect

1. Under the action of high pressure and high speed, the tension of the mold will increase, causing overflow, so the operator needs to adjust the injection speed and injection time according to the thickness of the mold product. The filling of thin products should be high-speed and fast, while for thick products, low-speed filling should be used.

2. Some operators often choose to inject more molten material in order to avoid the depression of the injection mold, but doing so will certainly solve the problem, but it will lead to overflow. Therefore, when we encounter this situation, we should deal with it by extending the injection time or pressure holding time.

The above is about the analysis of the reasons for the overflow of injection mold. The editor mainly introduces the equipment, mold and process, and hopes to help you.

Copyright: Shenzhen Zhongyuan Plastic Co., Ltd. | mold processing customized manufacturer. If you want to know the processing price of the factory, how much is it, and which is good, please contact us Yue ICP Bei No. 17060480
主站蜘蛛池模板: 婷婷六月综合网 | 天堂v| 日韩中文字幕视频 | 天天看a | 亚洲 欧美 中文 日韩欧美 | 天堂综合网 | 天天都色 | 全黄大全大色全免费大片 | 手机看片日韩日韩 | 一区二区网站在线观看 | 日韩经典在线 | 色婷婷色 | 亚洲激情视频在线播放 | 欧美手机视频 | 一区二区三区在线播放视频 | 特黄a大片免费视频 | 天天综合网色中文字幕 | 欧美一区二区三区免费观看视频 | 午夜国产精品不卡在线观看 | 中文字幕亚洲一区 | 亚欧毛片基地国产毛片基地 | 天天干天天色综合 | 色橹橹欧美在线观看视频高清 | 影音先锋国产 | 天堂中文在线网 | 亚洲小视频在线播放 | 亚洲成a人片在线观看播放 亚洲成a人片在线观看www | 亚洲不卡 | 桃花视频在线观看免费迅雷 | 神马热 | 亚洲视频一区在线播放 | 五月天丁香婷婷综合久久 | 色小妹综合 | 日本精品高清一区二区2021 | 色狠狠色综合久久8狠狠色 色狠狠色综合吹潮 | 欧美一级久久久久久久大片 | 亚洲国产成人资源在线桃色 | 青娱乐自拍 | 青青草原在线免费观看视频 | 在线视频第一页 | 色综色天天综合网 |